XLNT 125mm Pneumatic Sander Without Hose – XTSWH 97

The XLNT Pneumatic Sander XTSWH 97 is a compact air-powered sanding machine designed for automotive bodywork, wood sanding and industrial surface-finishing applications. It features a listed 10,000 RPM no-load speed, 90 PSI air-pressure requirement, 125mm sanding pad and 5mm orbit.

The compact pneumatic body is designed for easier single-hand operation during suitable surface-preparation and sanding work. This model is supplied without an air hose, allowing professional users to connect it to an existing compatible pneumatic system.

10,000 RPM High-Speed Pneumatic Sanding

The XLNT XTSWH 97 has a listed no-load speed of 10,000 RPM. This supports efficient sanding and finishing when the machine is connected to a compressor capable of delivering the required pressure and continuous airflow.

Actual working speed may vary depending on:

• Compressor airflow
• Air-pressure stability
• Hose internal diameter
• Air-fitting size
• Regulator setting
• Abrasive grit
• Surface material
• Pressure applied by the operator

Avoid pressing the sander excessively against the workpiece because excessive pressure can reduce sanding speed and create uneven results.

125mm or 5-Inch Sanding Pad

The product uses a listed 125mm sanding pad, equivalent to approximately 5 inches. This pad size provides practical coverage for automotive panels, wooden surfaces and suitable industrial finishing work.

Before purchasing replacement sanding discs, confirm:

• Backing-pad attachment type
• Hook-and-loop or adhesive system
• Dust-hole pattern
• Backing-pad thread
• Compatible abrasive thickness
• Replacement-pad compatibility

Matching only the 125mm diameter may not guarantee that every sanding disc or backing pad will fit correctly.

5mm Orbit for Surface Preparation

The machine has a listed 5mm orbit. This can support general sanding, surface preparation and controlled material removal when used with a suitable abrasive.

The current page does not clarify whether the machine operates as:

• Random orbital
• Dual action
• Standard orbital
• Rotary orbital

Do not publish any of these mechanism-specific terms until the manufacturer or product label confirms the exact operation.

90 PSI Air-Pressure Requirement

The XLNT XTSWH 97 requires a listed operating pressure of 90 PSI. The connected air compressor must maintain this pressure while the machine is running.

Reaching 90 PSI alone does not confirm compressor compatibility. The compressor must also provide adequate continuous airflow, normally stated in:

• CFM
• SCFM
• Litres per minute

The current page does not publish the required airflow. This is the most important missing specification for customers selecting a compatible compressor.

Air Hose Not Included

This model is specifically listed without an air hose. Buyers must arrange a suitable pneumatic hose and compatible fittings separately.

Before selecting a hose, confirm:

• Recommended internal diameter
• Required hose length
• Maximum working-pressure rating
• Air-inlet thread size
• Connector type
• Compressor outlet fitting
• Required airflow capacity

A narrow or restrictive hose can reduce airflow and lower the sander’s practical performance.

Compact Body for Single-Hand Use

The product page describes the XTSWH 97 as having a compact pneumatic body suitable for easy single-hand operation. This can improve handling during repetitive sanding work and help users maintain better control across suitable surfaces.

The exact machine weight, grip dimensions, noise level and vibration value should be added to help professional buyers assess comfort during extended operation.

Automotive Sanding Applications

Automotive sanding is one of the listed applications. The machine can support suitable body-panel preparation, primer sanding and refinishing work when used with the correct abrasive disc and pressure setting.

Maintain extra care around:

• Panel edges
• Body lines
• Thin paint sections
• Plastic trim
• Rubber seals
• Badges and stickers
• Electrical components

Begin with the least aggressive abrasive suitable for the job.

Wood Sanding Applications

Wood sanding is also listed as a suitable use. The pneumatic sander may be used for appropriate furniture preparation, timber smoothing and coating preparation when equipped with the correct abrasive grit.

Test the abrasive on a small hidden area before sanding the complete workpiece, especially when working with soft timber, veneer or coated surfaces.

Industrial Sanding Applications

The product is positioned for industrial sanding tasks and professional sanding users. It can support suitable workshop surface preparation where a compressed-air supply is already available.

Application suitability depends on:

• Surface material
• Abrasive type
• Airflow
• Pressure stability
• Operator technique
• Dust-management method
• Required finish

Choosing the Correct Abrasive Grit

Coarse Grit:

Suitable for compatible coating removal and heavier levelling.

Medium Grit:

Suitable for general preparation and surface smoothing.

Fine Grit:

Suitable for primer preparation and finishing.

Very Fine Grit:

Suitable for specialised refinishing and final surface preparation.

Always select the abrasive according to the surface material and required finish.

Compressor Compatibility

Before purchasing or connecting an air compressor, confirm:

• Air consumption in CFM
• Air consumption in L/min
• Recommended compressor free-air delivery
• Recommended compressor tank size
• Air-inlet thread
• Recommended hose internal diameter
• Maximum approved pressure
• Pneumatic-tool lubrication requirement

A small compressor may reach 90 PSI but lose pressure quickly if it cannot supply sufficient continuous airflow.

How to Use

1. Inspect the pneumatic sander, backing pad, abrasive disc and air connection.
2. Confirm that the compressor is switched off before connecting the sander.
3. Fit a compatible 125mm abrasive disc securely.
4. Connect a suitable air hose and compatible fitting.
5. Set the compressor regulator according to the approved operating pressure.
6. Hold the sanding pad flat against the workpiece.
7. Begin sanding using light and even pressure.
8. Move the machine continuously using overlapping passes.
9. Avoid holding the sander in one position for too long.
10. Disconnect the air supply before changing abrasives, cleaning or servicing the tool.

Safety Instructions

• Wear safety glasses.
• Use suitable hearing protection.
• Wear respiratory protection when sanding dusty materials.
• Secure the workpiece before operation.
• Never exceed the approved air pressure.
• Do not use a damaged hose or connector.
• Disconnect the air supply before changing abrasives.
• Keep hands away from the moving sanding pad.
• Never direct compressed air toward people or animals.
• Use appropriate dust extraction where required.
• Follow the verified pneumatic-tool lubrication instructions.
• Store the machine in a clean and dry location.

9. Key Product Features

• 10,000 RPM no-load speed
• 90 PSI operating-pressure requirement
• 125mm sanding-pad size
• Approximately 5-inch pad diameter
• 5mm orbit
• Compressed-air operation
• Air hose not included
• Compact pneumatic body
• Easy single-hand use
• Suitable for industrial sanding
• Suitable for automotive sanding
• Suitable for wood sanding
• Designed for professional sanding users
• Six-month service warranty
• Optional extended warranty