THOR 850W Angle Grinder for Cutting and Grinding Work
The THOR THAG38 850W Angle Grinder is a compact corded power tool designed for suitable metal cutting, surface grinding, deburring, weld finishing and fabrication applications. Its 100mm or 4-inch disc capacity makes it practical for workshops, repair centres, fabrication units, maintenance technicians and users who require a manageable grinder for regular work.
The angle grinder has a supplier-listed power rating of 850W and operates on a rated electrical supply of 220V at 50Hz. Its corded electric design provides direct power wherever a suitable electrical connection is available, without requiring batteries or charging.
An auxiliary side handle, safety guard, flange components and pin wrench are shown with the THOR THAG38. These accessories support better machine control, safer disc positioning and convenient accessory installation.
100mm or 4-Inch Disc Capacity
The THOR THAG38 is designed for a 100mm or 4-inch disc.
Different grinder accessories are intended for different applications. The correct compatible accessory should be selected according to the material and required job.
Suitable accessory types may include:
- Cutting discs for compatible metal cutting
- Grinding wheels for surface grinding
- Flap discs for finishing and smoothing
- Compatible wire accessories for surface preparation
Every accessory must match the machine’s 100mm disc capacity and confirmed operating speed. Never install an oversized disc or an accessory with a lower speed rating than the grinder.
850W Corded Electric Performance
The supplier image lists a rated power of 850W. This makes the THOR THAG38 suitable for compatible everyday cutting, grinding, deburring and workshop applications.
Actual performance will depend on:
- Material type and thickness
- Disc type and condition
- Electrical supply
- Working angle
- Applied pressure
- Operator technique
Allow the rotating accessory to perform the cutting or grinding work. Applying excessive pressure may slow the disc, reduce efficiency and place unnecessary load on the machine.
Supplier-Listed 1100 RPM Speed
The supplier image lists the no-load speed as 1100 RPM.
However, the current BUYBOX page displays 11,000 RPM. The correct value should therefore be checked on the physical machine label or carton before final publication.
Until verified, the safest specification format is:
Supplier-Listed No-Load Speed: 1100 RPM — confirmation recommended
Do not automatically change this figure or use it in advertising campaigns until the correct speed is confirmed.
Auxiliary Side Handle for Improved Control
An auxiliary side handle is shown with the THOR THAG38. It allows the operator to hold the angle grinder with both hands, improving control and stability during cutting and grinding.
The handle should be fitted securely before operation. A firm two-handed grip is particularly important when starting the machine, working on harder material or controlling possible kickback.
The operator should maintain a balanced stance and keep hands away from the rotating disc.
Safety Guard for Operator Protection
A safety guard is shown with the grinder. The guard creates a protective barrier between the operator and the rotating accessory.
The guard should be fitted and positioned correctly before the machine is switched on. It should not be removed merely to gain additional cutting access.
The operator should remain outside the direct line of the rotating disc whenever possible.
Flange Components and Pin Wrench
Flange components are shown with the THOR THAG38. These parts help secure a compatible disc to the grinder spindle.
A pin-style wrench is also visible. It is used to tighten or loosen the flange while installing or removing the disc.
The machine must always be switched off and unplugged before changing an accessory. Ensure the disc is centred, properly seated and securely tightened before operation.
Suitable Applications
The THOR THAG38 can be considered for:
Metal cutting with a compatible disc
Surface grinding
Weld finishing
Deburring sharp metal edges
Fabrication work
Workshop repairs
Maintenance jobs
Preparing metal surfaces
Cutting suitable pipes, rods and sections
Removing suitable surface deposits
Actual suitability depends on the accessory selected and the material being worked on.
Safety and Operating Guidance
Wear safety glasses or a face shield, hearing protection, gloves and suitable protective clothing while operating the grinder.
Inspect the power cable, plug, safety guard, side handle, flange components and disc before every use.
Do not use a disc that is cracked, chipped, bent, wet, expired or incorrectly rated for the machine.
Allow the grinder to reach operating speed before contacting the workpiece. Keep the power cable away from the rotating disc and hot material.
Direct sparks away from the operator, electrical cables, fuel, paint, paper, sawdust and other flammable materials.
Key Features
850W rated power
100mm or 4-inch disc diameter
220V rated voltage
50Hz rated frequency
1100 RPM supplier-listed no-load speed
Corded electric operation
Compact angle-grinder body
Auxiliary side handle
Safety guard
Flange components shown
Pin wrench shown
Product box shown
Suitable for compatible cutting and grinding
Suitable for deburring and fabrication work
Two-handed operating support
THOR 850W Angle Grinder for Cutting and Grinding Work
The THOR THAG38 850W Angle Grinder is a compact corded power tool designed for suitable metal cutting, surface grinding, deburring, weld finishing and fabrication applications. Its 100mm or 4-inch disc capacity makes it practical for workshops, repair centres, fabrication units, maintenance technicians and users who require a manageable grinder for regular work.
The angle grinder has a supplier-listed power rating of 850W and operates on a rated electrical supply of 220V at 50Hz. Its corded electric design provides direct power wherever a suitable electrical connection is available, without requiring batteries or charging.
An auxiliary side handle, safety guard, flange components and pin wrench are shown with the THOR THAG38. These accessories support better machine control, safer disc positioning and convenient accessory installation.
100mm or 4-Inch Disc Capacity
The THOR THAG38 is designed for a 100mm or 4-inch disc.
Different grinder accessories are intended for different applications. The correct compatible accessory should be selected according to the material and required job.
Suitable accessory types may include:
- Cutting discs for compatible metal cutting
- Grinding wheels for surface grinding
- Flap discs for finishing and smoothing
- Compatible wire accessories for surface preparation
Every accessory must match the machine’s 100mm disc capacity and confirmed operating speed. Never install an oversized disc or an accessory with a lower speed rating than the grinder.
850W Corded Electric Performance
The supplier image lists a rated power of 850W. This makes the THOR THAG38 suitable for compatible everyday cutting, grinding, deburring and workshop applications.
Actual performance will depend on:
- Material type and thickness
- Disc type and condition
- Electrical supply
- Working angle
- Applied pressure
- Operator technique
Allow the rotating accessory to perform the cutting or grinding work. Applying excessive pressure may slow the disc, reduce efficiency and place unnecessary load on the machine.
Supplier-Listed 1100 RPM Speed
The supplier image lists the no-load speed as 1100 RPM.
However, the current BUYBOX page displays 11,000 RPM. The correct value should therefore be checked on the physical machine label or carton before final publication.
Until verified, the safest specification format is:
Supplier-Listed No-Load Speed: 1100 RPM — confirmation recommended
Do not automatically change this figure or use it in advertising campaigns until the correct speed is confirmed.
Auxiliary Side Handle for Improved Control
An auxiliary side handle is shown with the THOR THAG38. It allows the operator to hold the angle grinder with both hands, improving control and stability during cutting and grinding.
The handle should be fitted securely before operation. A firm two-handed grip is particularly important when starting the machine, working on harder material or controlling possible kickback.
The operator should maintain a balanced stance and keep hands away from the rotating disc.
Safety Guard for Operator Protection
A safety guard is shown with the grinder. The guard creates a protective barrier between the operator and the rotating accessory.
The guard should be fitted and positioned correctly before the machine is switched on. It should not be removed merely to gain additional cutting access.
The operator should remain outside the direct line of the rotating disc whenever possible.
Flange Components and Pin Wrench
Flange components are shown with the THOR THAG38. These parts help secure a compatible disc to the grinder spindle.
A pin-style wrench is also visible. It is used to tighten or loosen the flange while installing or removing the disc.
The machine must always be switched off and unplugged before changing an accessory. Ensure the disc is centred, properly seated and securely tightened before operation.
Suitable Applications
The THOR THAG38 can be considered for:
Metal cutting with a compatible disc
Surface grinding
Weld finishing
Deburring sharp metal edges
Fabrication work
Workshop repairs
Maintenance jobs
Preparing metal surfaces
Cutting suitable pipes, rods and sections
Removing suitable surface deposits
Actual suitability depends on the accessory selected and the material being worked on.
Safety and Operating Guidance
Wear safety glasses or a face shield, hearing protection, gloves and suitable protective clothing while operating the grinder.
Inspect the power cable, plug, safety guard, side handle, flange components and disc before every use.
Do not use a disc that is cracked, chipped, bent, wet, expired or incorrectly rated for the machine.
Allow the grinder to reach operating speed before contacting the workpiece. Keep the power cable away from the rotating disc and hot material.
Direct sparks away from the operator, electrical cables, fuel, paint, paper, sawdust and other flammable materials.
Key Features
850W rated power
100mm or 4-inch disc diameter
220V rated voltage
50Hz rated frequency
1100 RPM supplier-listed no-load speed
Corded electric operation
Compact angle-grinder body
Auxiliary side handle
Safety guard
Flange components shown
Pin wrench shown
Product box shown
Suitable for compatible cutting and grinding
Suitable for deburring and fabrication work
Two-handed operating support
Warranty
Product Description
Shipping
Seller Information
